Jump to content

Storage area network

From Wikipedia, the free encyclopedia

Fibre Channel
Layer 4. Protocol mapping
LUN masking
Layer 3. Common services
Layer 2. Network
Fibre Channel fabric
Fibre Channel zoning
Registered state change notification
Layer 1. Data link
Fibre Channel 8b/10b encoding
Layer 0. Physical

A storage area network (SAN) or storage network is a computer network which provides access to consolidated, block-level data storage. SANs are primarily used to access data storage devices, such as disk arrays and tape libraries from servers so that the devices appear to the operating system as direct-attached storage. A SAN typically is a dedicated network of storage devices not accessible through the local area network (LAN).

Although a SAN provides only block-level access, file systems built on top of SANs do provide file-level access and are known as shared-disk file systems.

Newer SAN configurations enable hybrid SAN[1] and allow traditional block storage that appears as local storage but also object storage for web services through APIs.

Storage architectures

[edit]
The Fibre Channel SAN connects servers to storage via Fibre Channel switches.

Storage area networks (SANs) are sometimes referred to as network behind the servers[2]: 11  and historically developed out of a centralized data storage model, but with its own data network. A SAN is, at its simplest, a dedicated network for data storage. In addition to storing data, SANs allow for the automatic backup of data, and the monitoring of the storage as well as the backup process.[3]: 16–17  A SAN is a combination of hardware and software.[3]: 9  It grew out of data-centric mainframe architectures, where clients in a network can connect to several servers that store different types of data.[3]: 11  To scale storage capacities as the volumes of data grew, direct-attached storage (DAS) was developed, where disk arrays or just a bunch of disks (JBODs) were attached to servers. In this architecture, storage devices can be added to increase storage capacity. However, the server through which the storage devices are accessed is a single point of failure, and a large part of the LAN network bandwidth is used for accessing, storing and backing up data. To solve the single point of failure issue, a direct-attached shared storage architecture was implemented, where several servers could access the same storage device.[3]: 16–17 

DAS was the first network storage system and is still widely used where data storage requirements are not very high. Out of it developed the network-attached storage (NAS) architecture, where one or more dedicated file server or storage devices are made available in a LAN.[3]: 18  Therefore, the transfer of data, particularly for backup, still takes place over the existing LAN. If more than a terabyte of data was stored at any one time, LAN bandwidth became a bottleneck.[3]: 21–22  Therefore, SANs were developed, where a dedicated storage network was attached to the LAN, and terabytes of data are transferred over a dedicated high speed and bandwidth network. Within the SAN, storage devices are interconnected. Transfer of data between storage devices, such as for backup, happens behind the servers and is meant to be transparent.[3]: 22  In a NAS architecture data is transferred using the TCP and IP protocols over Ethernet. Distinct protocols were developed for SANs, such as Fibre Channel, iSCSI, Infiniband. Therefore, SANs often have their own network and storage devices, which have to be bought, installed, and configured. This makes SANs inherently more expensive than NAS architectures.[3]: 29 

Components

[edit]
Dual port 8 Gb FC host bus adapter card

SANs have their own networking devices, such as SAN switches. To access the SAN, so-called SAN servers are used, which in turn connect to SAN host adapters. Within the SAN, a range of data storage devices may be interconnected, such as SAN-capable disk arrays, JBODS and tape libraries.[3]: 32, 35–36 

Host layer

[edit]

Servers that allow access to the SAN and its storage devices are said to form the host layer of the SAN. Such servers have host adapters, which are cards that attach to slots on the server motherboard (usually PCI slots) and run with a corresponding firmware and device driver. Through the host adapters the operating system of the server can communicate with the storage devices in the SAN.[4]: 26 

In Fibre channel deployments, a cable connects to the host adapter through the gigabit interface converter (GBIC). GBICs are also used on switches and storage devices within the SAN, and they convert digital bits into light impulses that can then be transmitted over the Fibre Channel cables. Conversely, the GBIC converts incoming light impulses back into digital bits. The predecessor of the GBIC was called gigabit link module (GLM).[4]: 27 

Fabric layer

[edit]
Qlogic SAN-switch with optical Fibre Channel connectors installed

The fabric layer consists of SAN networking devices that include SAN switches, routers, protocol bridges, gateway devices, and cables. SAN network devices move data within the SAN, or between an initiator, such as an HBA port of a server, and a target, such as the port of a storage device.

When SANs were first built, hubs were the only devices that were Fibre Channel capable, but Fibre Channel switches were developed and hubs are now rarely found in SANs. Switches have the advantage over hubs that they allow all attached devices to communicate simultaneously, as a switch provides a dedicated link to connect all its ports with one another.[4]: 34  When SANs were first built, Fibre Channel had to be implemented over copper cables, these days multimode optical fibre cables are used in SANs.[4]: 40 

SANs are usually built with redundancy, so SAN switches are connected with redundant links. SAN switches connect the servers with the storage devices and are typically non-blocking allowing transmission of data across all attached wires at the same time.[4]: 29  SAN switches are for redundancy purposes set up in a meshed topology. A single SAN switch can have as few as 8 ports and up to 32 ports with modular extensions.[4]: 35  So-called director-class switches can have as many as 128 ports.[4]: 36 

In switched SANs, the Fibre Channel switched fabric protocol FC-SW-6 is used under which every device in the SAN has a hardcoded World Wide Name (WWN) address in the host bus adapter (HBA). If a device is connected to the SAN its WWN is registered in the SAN switch name server.[4]: 47  In place of a WWN, or worldwide port name (WWPN), SAN Fibre Channel storage device vendors may also hardcode a worldwide node name (WWNN). The ports of storage devices often have a WWN starting with 5, while the bus adapters of servers start with 10 or 21.[4]: 47 

Storage layer

[edit]
Fibre Channel is a layered technology that starts at the physical layer and progresses through the protocols to the upper-level protocols like SCSI and SBCCS.

The serialized Small Computer Systems Interface (SCSI) protocol is often used on top of the Fibre Channel switched fabric protocol in servers and SAN storage devices. The Internet Small Computer Systems Interface (iSCSI) over Ethernet and the Infiniband protocols may also be found implemented in SANs, but are often bridged into the Fibre Channel SAN. However, Infiniband and iSCSI storage devices, in particular, disk arrays, are available.[4]: 47–48 

The various storage devices in a SAN are said to form the storage layer. It can include a variety of hard disk and magnetic tape devices that store data. In SANs, disk arrays are joined through a RAID which makes a lot of hard disks look and perform like one big storage device.[4]: 48  Every storage device, or even partition on that storage device, has a logical unit number (LUN) assigned to it. This is a unique number within the SAN. Every node in the SAN, be it a server or another storage device, can access the storage by referencing the LUN. The LUNs allow for the storage capacity of a SAN to be segmented and for the implementation of access controls. A particular server, or a group of servers, may, for example, be only given access to a particular part of the SAN storage layer, in the form of LUNs. When a storage device receives a request to read or write data, it will check its access list to establish whether the node, identified by its LUN, is allowed to access the storage area, also identified by a LUN.[4]: 148–149  LUN masking is a technique whereby the host bus adapter and the SAN software of a server restrict the LUNs for which commands are accepted. In doing so LUNs that should never be accessed by the server are masked.[4]: 354  Another method to restrict server access to particular SAN storage devices is fabric-based access control, or zoning, which is enforced by the SAN networking devices and servers. Under zoning, server access is restricted to storage devices that are in a particular SAN zone.[5]

Network protocols

[edit]

A mapping layer to other protocols is used to form a network:

Storage networks may also be built using Serial Attached SCSI (SAS) and Serial ATA (SATA) technologies. SAS evolved from SCSI direct-attached storage. SATA evolved from Parallel ATA direct-attached storage. SAS and SATA devices can be networked using SAS Expanders.

Examples of stacked protocols using SCSI
Applications
SCSI Layer
FCP FCP FCP FCP iSCSI iSER SRP
FCIP iFCP
TCP RDMA Transport
FCoE IP IP or InfiniBand Network
FC Ethernet Ethernet or InfiniBand Link

Software

[edit]

The Storage Networking Industry Association (SNIA) defines a SAN as "a network whose primary purpose is the transfer of data between computer systems and storage elements". But a SAN does not just consist of a communication infrastructure, it also has a software management layer. This software organizes the servers, storage devices, and the network so that data can be transferred and stored. Because a SAN does not use direct attached storage (DAS), the storage devices in the SAN are not owned and managed by a server.[2]: 11  A SAN allows a server to access a large data storage capacity and this storage capacity may also be accessible by other servers.[2]: 12  Moreover, SAN software must ensure that data is directly moved between storage devices within the SAN, with minimal server intervention.[2]: 13 

SAN management software is installed on one or more servers and management clients on the storage devices. Two approaches have developed in SAN management software: in-band and out-of-band management. In-band means that management data between server and storage devices is transmitted on the same network as the storage data. While out-of-band means that management data is transmitted over dedicated links.[2]: 174  SAN management software will collect management data from all storage devices in the storage layer. This includes info on read and write failures, storage capacity bottlenecks and failure of storage devices. SAN management software may integrate with the Simple Network Management Protocol (SNMP).[2]: 176 

In 1999 Common Information Model (CIM), an open standard, was introduced for managing storage devices and to provide interoperability, The web-based version of CIM is called Web-Based Enterprise Management (WBEM) and defines SAN storage device objects and process transactions. Use of these protocols involves a CIM object manager (CIMOM), to manage objects and interactions, and allows for the central management of SAN storage devices. Basic device management for SANs can also be achieved through the Storage Management Interface Specification (SMI-S), were CIM objects and processes are registered in a directory. Software applications and subsystems can then draw on this directory.[2]: 177  Management software applications are also available to configure SAN storage devices, allowing, for example, the configuration of zones and LUNs.[2]: 178 

Ultimately SAN networking and storage devices are available from many vendors and every SAN vendor has its own management and configuration software. Common management in SANs that include devices from different vendors is only possible if vendors make the application programming interface (API) for their devices available to other vendors. In such cases, upper-level SAN management software can manage the SAN devices from other vendors.[2]: 180 

Filesystems support

[edit]

In a SAN, data is transferred, stored and accessed on a block level. As such, a SAN does not provide data file abstraction, only block-level storage and operations. Server operating systems maintain their own file systems on their own dedicated, non-shared LUNs on the SAN, as though they were local to themselves. If multiple systems were simply to attempt to share a LUN, these would interfere with each other and quickly corrupt the data. Any planned sharing of data on different computers within a LUN requires software. File systems have been developed to work with SAN software to provide file-level access. These are known as shared-disk file system.

In media and entertainment

[edit]

Video editing systems require very high data transfer rates and very low latency. SANs in media and entertainment are often referred to as serverless due to the nature of the configuration which places the video workflow (ingest, editing, playout) desktop clients directly on the SAN rather than attaching to servers. Control of data flow is managed by a distributed file system. Per-node bandwidth usage control, sometimes referred to as quality of service (QoS), is especially important in video editing as it ensures fair and prioritized bandwidth usage across the network.

Quality of service

[edit]

SAN Storage QoS enables the desired storage performance to be calculated and maintained for network customers accessing the device. Some factors that affect SAN QoS are:

  • Bandwidth – The rate of data throughput available on the system.
  • Latency – The time delay for a read/write operation to execute.
  • Queue depth – The number of outstanding operations waiting to execute to the underlying disks (traditional or solid-state drives).

Alternatively, over-provisioning can be used to provide additional capacity to compensate for peak network traffic loads. However, where network loads are not predictable, over-provisioning can eventually cause all bandwidth to be fully consumed and latency to increase significantly resulting in SAN performance degradation.

Storage virtualization

[edit]

Storage virtualization is the process of abstracting logical storage from physical storage. The physical storage resources are aggregated into storage pools, from which the logical storage is created. It presents to the user a logical space for data storage and transparently handles the process of mapping it to the physical location, a concept called location transparency. This is implemented in modern disk arrays, often using vendor-proprietary technology. However, the goal of storage virtualization is to group multiple disk arrays from different vendors, scattered over a network, into a single storage device. The single storage device can then be managed uniformly.[8]

See also

[edit]

References

[edit]
  1. ^ "Water Panther Expanse SAN Series | Enterprise Data Center Hard Drives & SSDs". Water Panther. Archived from the original on 18 July 2022. Retrieved 18 July 2022.
  2. ^ a b c d e f g h i Jon Tate; Pall Beck; Hector Hugo Ibarra; Shanmuganathan Kumaravel; Libor Miklas (2017). "Introduction to Storage Area Networks" (PDF). Red Books, IBM. Archived (PDF) from the original on 1 January 2020. Retrieved 15 September 2011.
  3. ^ a b c d e f g h i Special Edition: Using Storage Area Networks. Que Publishing. 2002. ISBN 978-0-7897-2574-5.
  4. ^ a b c d e f g h i j k l m Christopher Poelker; Alex Nikitin, eds. (2009). Storage Area Networks For Dummies. John Wiley & Sons. ISBN 978-0-470-47134-0.
  5. ^ Richard Barker; Paul Massiglia (2002). Storage Area Network Essentials: A Complete Guide to Understanding and Implementing SANs. John Wiley & Sons. p. 198. ISBN 978-0-471-26711-9.
  6. ^ "TechEncyclopedia: IP Storage". Archived from the original on 9 April 2009. Retrieved 9 December 2007.
  7. ^ "TechEncyclopedia: SANoIP". Archived from the original on 9 April 2009. Retrieved 9 December 2007.
  8. ^ PC Magazine. "Virtual Storage". PC Magazine Encyclopedia. Archived from the original on 30 August 2019. Retrieved 17 October 2017.
[edit]